Extending SSD Lifespan with Comprehensive Non-Volatile Memory-Based Write Buffers

Journal of Computer Science and Technology - New non-volatile memory (NVM) technologies are expected to replace main memory DRAM (dynamic random access memory) in the near future. NAND flash...     

基于状态观测器的电镀液温度状态反馈控制系统

针对电镀液温度控制系统,引入状态反馈控制。相对于传统的反馈控制,本方法可以获得更优异的性能。另外,考虑到镀液温度控制具有纯迟延的特点,提出了一种消去纯迟延的方法。仿真验证结果显示,控制效果良好。     

Calorimetric study of ytterbium orthovanadate YbVO4 polycrystalline ceramics

The heat capacity of ytterbium orthovanadate was first measured by adiabatic calorimetry in the temperature range T?=?12.28–344.06?K. No obvious anomalies were observed on the curve obtained. The values of standard thermodynamic functions in the temperature range T?=?0–400 K were calculated. Based on low-temperature calorimetry data obtained, previously published data on the high-temperature heat capacity of ytterbium orthovanadate were corrected. The anomalous contribution to heat capacity for YbVO₄ was compared with the data known for YbPO₄.     

The influence of activated carbon as an additive in anode materials for low temperature solid oxide fuel cells

The effects of activated carbon (AC) as an additive in multi-oxide nano composite LiNiCuZn–O for application as anode in solid oxide fuel cell (SOFC) is reported. The composite was synthesized using solid state reactions method with varying content of AC in range 0.1%–0.9% for use as anode in the cell. The cell was composed of the synthesized composite as anode, LiNiCuZn–O as cathode and Samaria doped ceria (SDC) as electrolyte. The prepared composites were characterized for morphology and crystal structure by scanning electron microscope (SEM) and x-ray diffraction (XRD) respectively. Furthermore, the crystallite sizes of LiNiCuZn–O and LiNiCuZn–O with AC as an additive have been found in the range from 50 nm to 70 nm. The prepared composite materials were observed porous and the porosity of the sample having 0.5% additive was found highest. The conductivity and power density of the SOFC were studied at temperature of 600 °C. The maximum value of conductivity was found as 4.79 S/cm for the composite containing 0.5% AC as measured by using 4-probe method. The maximum value of power density of the fuel cell with anode comprising of 0.5% AC along with the mentioned cathode and the electrolyte was 455 mW/cm². Therefore, out of the compositions studied, the composite comprising of LiNiCuZn–O with 0.5% AC offered best performance for anode in the cell. This oxide composite is reported as a potential candidate for use as anode in low temperature SOFCs.     

A mixed collector system for phosphate flotation

Flotation has been used in industry for more than a half century as the primary technique for upgrading phosphate. While the flotation of phosphate was inefficient when oleic acid was used alone as a collector, therefore a mixed collector of oleic acid (HOl), linoleic acid (LA) and linolenic acid (LNA) was employed to improve the recovery of phosphate flotation. The batch flotation results showed that the optimal composition of the mixed collector was 54 wt.% HOl, 36 wt.% LA and 10 wt.% LNA. Additionally, the effect of pH on the mixed collector application was studied while considering the surface tension, contact angle and micro-flotation. The results showed that the mixed collector should be used at a pH of 9.5. Above a pH of 9.5, the adsorption of fatty acids dimers on the apatite surface hindered phosphate flotation. The influence of the mixed collector assembly on apatite flotation was also investigated. It was demonstrated that due to its low critical micelle concentration, a sufficiently hydrophobic apatite surface could be generated at a collector concentration of 60 mg/L. In addition, zeta potential experiments suggested that collector adsorption was governed by chemisorption. FTIR and XPS spectra studies further indicated that the chemical reaction involved the carboxyl groups of fatty acids and Ca species at the apatite surface for each fatty acid in the mixed collector.     

Classification and regression models of audio and vibration signals for machine state monitoring in precision machining systems

We present a data-driven method for monitoring machine status in manufacturing processes. Audio and vibration data from precision machining are used for inference in two operating scenarios: (a) variable machine health states (anomaly detection); and (b) settings of machine operation (state estimation). Audio and vibration signals are first processed through Fast Fourier Transform and Principal Component Analysis to extract transformed and informative features. These features are then used in the training of classification and regression models for machine state monitoring. Specifically, three classifiers (K-nearest neighbors, convolutional neural networks and support vector machines) and two regressors (support vector regression and neural network regression) were explored, in terms of their accuracy in machine state prediction. It is shown that the audio and vibration signals are sufficiently rich in information about the machine that 100% state classification accuracy could be accomplished. Data fusion was also explored, showing overall superior accuracy of data-driven regression models.     

Solid state reactions between SiC and Ir

Reactivity between SiC and Ir as a function of SiC-crystallinity was investigated by diffusion bonding technique under a vacuum and over the temperature range of 1200–1450 °C. As reaction products, various Ir-silicides and free unreacted-C were detected. Reactivity is strongly affected by the temperature and SiC-crystallinity involving a series of interactions, from “no reaction” to “massive exothermic reactions”. In particular, interfacial phenomena are more pronounced by the presence of defects and grain boundaries.Solid state reactions result in formation of fine C-precipitates rearranged in a quasi-periodic microstructure. On the contrary, clustering of highly ordered C-precipitates (C-graphitized) occurs after “massive reactions” take place.A relationship between the degree of graphitization (from 1 to multi-layers of graphene), temperature and SiC crystallinity was found by Raman spectroscopy. 2D-layering phenomenon is enhanced in polycrystalline SiC at high temperature.     

Plasmonic-excitonic multi-hybrid glass-based nanocomposites incorporating Ag plus core-shell CdSe/CdS and alloyed CdSxSe1−x nanoparticles

Successful fabrication of glass-based hybrid nanocomposites (GHNCs) incorporating Ag, core-shell CdSe/CdS and CdS_xSe_1?x nanoparticles (NPs) is herein reported. Both metallic (Ag) and semiconductor (CdSe/CdS) NPs were pre-synthesized, suspended in colloids and added into the sol-gel reaction medium which was used to fabricate the GHNCs. During fabrication of the nanocomposites a fraction (20–60%) of core-shell CdSe/CdS NPs was alloyed into CdS_xSe_1?x (0.20 < x < 0.35) NPs without changing morphology. Modulation of in situ alloying is possible via the relative content of organics added into the sol-gel protocol. Within colloids Ag (core-shell CdSe/CdS) NPs presented average diameter and polydispersity index of 49.5 nm (4.2 nm) and 0.41 (0.21), respectively. On the other hand, the Ag (core-shell CdSe/CdS) NPs’ average diameter and polydispersity index assessed from the GHNCs were respectively 51.5 nm (4.1 nm) and 0.43 (0.25), revealing negligible aggregation of the nanophases within the glass template. The new GHNCs herein introduced presented two independent excitonic transitions associated to homogenously dispersed semiconductor NPs, peaking around 420 nm (core-shell CdSe/CdS) and 650 nm (CdS_xSe_1?x) and matching the plasmonic resonance (Ag NPs) in the 400–500 nm range. We envisage that the new GHNCs represent very promising candidates for superior light manipulation while illuminated with multiple laser beams in quantum interference-based devices.     

Active disturbance rejection based trajectory linearization control for hypersonic reentry vehicle with bounded uncertainties

This paper investigates a novel compound control scheme combined with the advantages of trajectory linearization control (TLC) and alternative active disturbance rejection control (ADRC) for hypersonic reentry vehicle (HRV) attitude tracking system with bounded uncertainties. Firstly, in order to overcome actuator saturation problem, nonlinear tracking differentiator (TD) is applied in the attitude loop to achieve fewer control consumption. Then, linear extended state observers (LESO) are constructed to estimate the uncertainties acting on the LTV system in the attitude and angular rate loop. In addition, feedback linearization (FL) based controllers are designed using estimates of uncertainties generated by LESO in each loop, which enable the tracking error for closed-loop system in the presence of large uncertainties to converge to the residual set of the origin asymptotically. Finally, the compound controllers are derived by integrating with the nominal controller for open-loop nonlinear system and FL based controller. Also, comparisons and simulation results are presented to illustrate the effectiveness of the control strategy.     

Temperature cycling and its effect on mechanical behaviours of highporosity chalks

Temperature history can have a significant effect on the strength of water-saturated chalk.In this study,hydrostatic stress cycles are applied to understand the mechanical response of chalk samples exposed to temperature cycling between each stress cycle,compared to the samples tested at a constant temperature.The total accumulated strain during a stress cycle and the irreversible strain are reported.Chalk samples from Kansas(USA)and Mons(Belgium),with different degrees of induration(i.e.amount of contact cementation),were used.The samples were saturated with equilibrated water(polar)and nonpolar Isopar H oil to quantify water weakening.All samples tested during 10 stress cycles with varying temperature(i.e.temperature cycled in between each stress cycle)accumulated more strain than those tested at constant temperatures.All the stress cycles were performed at 30℃.The two chalk types behaved similarly when saturated with Isopar H oil,but differently when saturated with water.When saturated with water,the stronger Kansas chalk accumulated more total strain and more irreversible strain within each stress cycle than the weaker Mons chalk.